For systems with voltage increase for starting. Use with 1.8ohm ballast resistor (supplied). This coil provides up to 70% more energy for starting and has sufficient energy reserves for acceleration and at high speeds. For engines up to 8 cylinders.IGNITION COILS
Ballast and Non-Ballast Ignition Systems
Contact breaker (points) type ignition systems, as fitted to most Ford models up to around 1980 (although it lasted up to 1987 for the Capri), can have either a ballast fitted in the wiring loom or not.What is a ballast?
Quite simply, it is a resistor that has the purpose of reducing the voltage to the coil.Why do some ignition systems have a ballast fitted where others do not?
Originally, all ignition systems did not have a ballast fitted which meant that the ignition system used a 12v coil with a 12v feed from the battery via the ignition switch. Such a system works fine when an engine is running, but problems can occur when starting the engine. The starter motor draws a huge current from the battery leaving less energy to create a spark across the spark plugs. The result is a weaker than normal spark which is not ideal for starting an engine. This problem is worsened by colder temperatures and/or a worn starter motor which will draw even more energy for starting and leave even less energy for sparking. To overcome such a problem, ignition systems were changed to run a lower voltage coil (usually 9v), and these coils could still give the same output as the original 12v coils.
In order to run such a coil, the 12v ignition feed runs through a ballast, reducing it to 9v at the coil.
To assist starting, a 12v feed (usually from the starter) bypasses the 9v ignition feed, giving the 9v coil a 12v feed. The result is a better than normal spark which is ideal for starting, particularly on cold damp mornings. As soon as the engine has started, the 12v feed is cut and the coil will run on the 9v ignition feed.How do I know which ignition system is fitted?
Ballast ignition systems were introduced in around 1970. Virtually all Ford models from this date should have a ballast fitted. To find out for sure, use a multimeter to check the voltage on the positive wire of the coil with the ignition on. Around 9v means you have a ballast, around 12v means you don’t.Which coil should I use with a ballast ignition system?
Without modifying your ignition system, you can use any standard ballast coil or we offer a performance ballast coil from Bosch (red coil 0221119030). Using a non-ballasted coil would mean that you are running a 12v coil on a 9v feed, resulting in a weak spark. You can however use such coils provided you remove the ballast resister.Which coil should I use with a non-ballast ignition system?
Use any standard non-ballast coil, or we offer a performance non-ballast coil from Bosch (blue coil 0221119027). Do not use a ballast coil. Although you may gain a performance advantage using such coils, failure will be imminent!
- Additional Information
Part No 0221119031 Product Group Ignition Coils Stock Status Stock Overdue - contact sales Catalogue 2018 Page Click HERE to view this part on page 85 of our 2018 catalogue Brand Logo Fits Model Variant Ford Anglia 105E, Ford Capri Mk1 (All), Ford Capri Mk2/Mk3 (All), Ford Cortina Mk1, Ford Cortina Mk2, Ford Cortina Mk3/Mk4/Mk5, Ford Escort Mk1 (All), Ford Escort Mk2 (All)
You may also be interested in the following product(s)
Distributor rotor arm: Fomoco SOHC Ford Pinto (points type only)/Essex V4 & V6/Taunus/Cologne & X/Flow 47700No Tax, Each £3.66 Taxed, Each £4.39
No Tax, Each £147.06 Taxed, Each £176.47
No Tax, Each £73.90 Taxed, Each £88.68
No Tax, Each £9.71 Taxed, Each £11.65
Motorcraft oil filter: SOHC Ford Pinto, YB Cosworth 4wd, Essex V4/V6, Taunus/Cologne V4/V6, RS2000 16v & 2.9 24v BOA EFL90No Tax, Each £10.16 Taxed, Each £12.19
No Tax, Each £63.34 Taxed, Each £76.01