DetailsHD cast substrate with lead indium overlay. Journal diameter 46.39/46.41mm
The new range of Mahle Motorsport bearings contains technology that has been transferred from Mahle’s F1 bearing technology. Manufactured with a “racing notch” – a notch which is machined in to the back of the bearing leaving the journal surface untouched.Benefits of the Racing Notch:
There are two main benefits of the racing notch:1. It enables the cross sectional area of the joint face to remain fully intact such that the hoop stresses in the bearing caused by the interference fit with the housing are equally distributed.
- A conventional notch requires a section of the material to be pressed back from the joint face which reduces the cross sectional area and therefore there is less material with which to support the load imposed by the interference fit of the bearing assembly.
- The racing notch allows the contact pressure between the bearing and housing to be maximised if required. This allows the housing to provide maximum support for the bearing and the optimum heat transfer from the bearing into the housing.
2. The bore of the bearing remains uninterrupted which creates a better surface for the formation of the oil film and it also removes an oil leakage path.
All bearings in this range are identified by laser marking as opposed to stamping.Benefits of Laser Marking:
The cheapest method of identifying a bearing is by stamping. For motorsport applications where higher temperatures are experienced, the effectiveness of heat transfer into the housing should not be compromised. If the stamping is heavy and extends quite far round the bearing causing poor back contact then the efficiency of heat transfer will be reduced.
Laser marking is an alternative method which creates smaller, more consistent marking which does not distort the backing and as such does not disrupt the back contact and subsequent heat transfer.Ford Zetec E 16v Silver Top -05/98
- Ford Escort Mk5 1.6 16v 1992-1995
- Ford Escort Mk5 1.8 & XR3i 1992-1995
- Ford Escort Mk6 1.6 16v 1995-2000
- Ford Escort Mk6 1.8 & GTi 1995-1998
- Ford Fiesta Mk3 Si 1.6 16v 1992-1995
- Ford Fiesta Mk3 XR2i 1.8 16v 1992-1995
- Ford Fiesta Mk3 RS1800 1.8 16v 1992-1995
- Ford Mondeo Mk1 1.6/1.8/2.0 16v 1992-1996
- Ford Mondeo Mk2 1.6/1.8/2.0 16v 1996-05/1998
- Ford Cougar 2.0 16v 1998-2002
- Ford Focus Mk1 1.8 16v 1998-2005
- Ford Focus Mk1 2.0 16v 1998-2005
- Ford Focus Mk1 ST170 2.0 16v 2002-2005 (Duratec ST)
- Ford Focus Mk1 RS 2.0 16v 2002-2003 (Duratec RS)
- Ford Mondeo Mk2 1.8/2.0 16v 05/1998-2000
- Additional Information
Part No VC1030/0.50 Fits Engine Type Ford Zetec E Product Group Crank Bearings & T/Washers Stock Status Stock Lead Time Typically 1-3 days Fits Engine Make Ford Catalogue 2018 Page Click HERE to view this part on page 21 of our 2018 catalogue Brand Logo Free Shipping
You may also be interested in the following product(s)
No Tax, Each £75.15 Taxed, Each £90.18
No Tax, Each £49.52 Taxed, Each £59.42
No Tax, Each £38.15 Taxed, Each £45.78
No Tax, Each £62.16 Taxed, Each £74.59
No Tax, Each £284.29 Taxed, Each £341.15
No Tax, Each £37.33 Taxed, Each £44.80