Ford Kent Crossflow Tuning Guide

Ford Kent Crossflow Engine

This engine was introduced in the Ford Mk2 Cortina and differs from the earlier units by having the carb on the left and the exhaust on the right - hence, ‘crossflow.’

They also varied from Pre-X/Flows in that the combustion chamber was shifted from the head to the bowl of the piston and were know as BIP engines (Bowl In Piston). Early heads also feature a small combustion chamber in the head too.

Early blocks bore the casting marks 681F and capacities you’ll find are, 940, 1098, 1298 and 1599. You’ll find a X/Flow fitted to Mk1/2 Escorts, Mk2/3 Cortinas, Mk1/2 Capris plus late Transits. Most cars came with a single choke Ford IV carb although the 1.3 and 1.6 GT models had a 32/36 DGV Weber twin choke.

1970 saw the big change to the thicker-walled 711M block with square mains caps, large diameter followers, wider cam lobes and modified crank seal. Also, the head was now completely flat.

There are two main capacities of 711M, determined by block height - the 1600 is 7/16" taller and you can see the difference between it and the 1300 by the space between the water pump and head. Also, the 1300 has 711M 6015 AA cast in the side whereas the 1600 ends in BA.

The engine was also fitted to 1.3 and 1.6 Mk1 Fiestas in the 80’s with a 771M casting. These feature no side engine mounts plus a shortened water pump and timing chain/crank area.

The final versions, OHV, HCS and Endura are similar but shorter versions and share very few if any inter-changeable parts and reverted back to the original pre-X/flow design of a three bearing crank.

Kents are quite easy to tune to GT spec, which usually means the biggest capacity block, slightly bigger valves (usually taken care of with a performance head), GT cam/A1, free flow exhaust and twin choke Weber - you should see around 80-90bhp. Switch to a Kent BCF2 or a 224 and you’ll be approaching 110bhp. For all builds we would recommend ARP rod bolts and replacement of the front pulley for a one piece steel item. The valve train should be strengthened with steel posts, spacers and rocker shaft to cope with the additional stresses caused by high lift cams, HD valve springs and higher revs. A double timing chain kit should also be fitted for the same reasons. Performance heads are available in both iron and brand new aluminium and all can be ordered with unleaded seats.

You can use the old Cosworth A-series cam profiles too, which are long duration and lower lift. However the current Kent Cams, high lift and short duration type are friendlier on emissions with less lobe overlap resulting in reduced un-burnt fuel down the exhaust.

Add a stage 2 head and Kent 224 and you’ll be pushing 115bhp although the favourite X/Flow cam is the 234 for 118-120bhp. You should get this with a re-jetted twin choke although twin 40 DCOE Webers would be better. This is an all round great cam and engine spec for the road.

A 244 cam and stage 3 head results in 135-145bhp, although, these figures are best achieved with a recommended maximum 83.5mm bore and forged Accralite pistons, giving 1700cc. There is a cheaper option in that the compression can be raised using modified 1300 pistons in the 1600 engine, giving a ratio of around 10.3:1. Capacity is easily increased with cast pistons available up to +0.090" oversize which will give 1696cc.

40 DCOEs tend to be on their maximum choke sizes at this stage so many switch to 45s. However this does result in lower gas speed and less low down torque, which is important on the road.

All side draughts need a side exit distributor cap (available for Lucas and Bosch distributors) to clear the inlet manifold and for convenience it’s best to fit an electronic ignition kit such as an Aldon Ignitor or Lumenition. For a complete ignition solution, our constant energy, non-vacuum modified Bosch distributor and coil kit is ideal for most modified engines.

This is about as far as you want to go on the road since you’ll be stretching the 7500-8000rpm limit of the crank. After this and you’ll ideally need steel components, which we have a superb range including cranks, rods, flywheels and forged pistons. To complement these we also have full-race spec heads to take the Kent as far as possible on the race track - currently that’s about 185bhp+.

Set Ascending Direction

1-20 of 41

Page
  1. Aluminium bellhousing: 2000E Bullet & Type 3 gearbox to Ford 4 cylinder (hydraulic clutch) BH1
    £319.90 (inc VAT)
    (ex VAT) £266.58

    Part Number: BH1

    Saves 4.625kg over iron bellhousing. Weight 3.7kg Learn More
    Available From Stock
  2. Bolt M12 x 30: Type 9 & Rocket\Type E gearbox (bellhousing bolt) & Ford Cosworth YB (camshaft bolt) BHB1
    £1.50 (inc VAT)
    (ex VAT) £1.25

    Part Number: BHB1

    12mm x 1.5 thread. Also fits Cosworth YB camshaft Learn More
    Available From Stock
  3. Standard clutch cover (pressure plate) 7.5" flat fingers 190mm: Escort Mk1 & Cortina Mk2 Ford X\Flow OHV Kent FP260C
    £59.95 (inc VAT)
    (ex VAT) £49.96

    Part Number: FP260C

    Use curved face release bearing Learn More
    Available From Stock
  4. Aluminium bellhousing Escort RS2000 Mk1\Mk2: Rocket\Type 9 gearbox to Ford 4 cylinder (LH & RH starter location) BH3
    £270.00 (inc VAT)
    (ex VAT) £225.00

    Part Number: BH3

    A high quality copy of the alloy bellhousing originally fitt.... Learn More
    Available From Stock
  5. Adaptor\spacer clutch carrier APC1
    £12.95 (inc VAT)
    (ex VAT) £10.79

    Part Number: APC1

    Many early clutch covers were fitted with thrust pads to the.... Learn More
    Available From Stock
  6. Clutch release bearing: Ford Cortina Mk1\Anglia 105E\Escort Mk1 Twin Cam, RS1600 & Mexico -73 HD3257
    £36.00 (inc VAT)
    (ex VAT) £30.00

    Part Number: HD3257

    Available From Stock
  7. Clutch release bearing: Ford Escort Mk1\APC1 clutch bearing spacer\MP315 extended release carrier HD3260
    £36.00 (inc VAT)
    (ex VAT) £30.00

    Part Number: HD3260

    Interchanges with HD3259 Learn More
    Available From Stock
  8. Clutch release bearing: Ford Cortina Mk2\APC1 clutch bearing spacer\MP315 extended release carrier HD3259
    £36.00 (inc VAT)
    (ex VAT) £30.00

    Part Number: HD3259

    Interchanges with HD3260 & HD3289. Learn More
    Available From Stock
  9. Clutch release bearing: Ford Cortina Mk3\4\5 & Capri 1.3\1.6 ECB110
    £24.50 (inc VAT)
    (ex VAT) £20.42

    Part Number: ECB110

    Models using Type 3 gearbox Learn More
    Available From Stock
  10. Clutch release bearing: Ford Escort Mk2 X\Flow Type 2 gearbox ECB114
    £27.95 (inc VAT)
    (ex VAT) £23.29

    Part Number: ECB114

    Available From Stock
  11. Magnesium bellhousing: 2000E Bullet & Type 3 gearbox to Ford 4 cylinder (hydraulic clutch) BH1A
    £618.00 (inc VAT)
    (ex VAT) £515.00

    Part Number: BH1A

    Saves 5.84kg over iron bellhousing Learn More
    No Stock - ordered on demand
  12. Aluminium bellhousing: SOHC Ford Pinto & X\Flow (LH starter) BH6A
    £331.20 (inc VAT)
    (ex VAT) £276.00

    Part Number: BH6A

    Fits Rocket & Type 9 gearbox with starter on LHS. Will fit C.... Learn More
    Available From Stock
  13. Aluminium bellhousing: ZF gearbox to Ford 4 cylinder (LH starter) BH2
    £550.00 (inc VAT)
    (ex VAT) £458.33

    Part Number: BH2

    Starter on LH side (exhaust side of engine) Learn More
    Stock Lead Time Typically 4-7 days
  14. Engine to bellhousing dirt plate: Ford X\Flow OHV Kent (not Mexico) RHD FP650
    £36.00 (inc VAT)
    (ex VAT) £30.00

    Part Number: FP650

    Does not fit 2000E bellhousings. RHD only. Learn More
    Available From Stock
  15. Std clutch kit Ford X\Flow OHV Kent Escort Mk1 619001406
    £96.95 (inc VAT)
    (ex VAT) £80.79

    Part Number: 619001406

    Supplied without release bearing . Learn More
    Available From Stock
  16. Standard clutch drive plate Ford X\Flow OHV Kent 190mm 7\8x20 spline C752AF
    £39.95 (inc VAT)
    (ex VAT) £33.29

    Part Number: C752AF

    Available From Stock
  17. AP Racing clutch drive plate 190mm: Ford Fiesta Mk1\Mk2 1.3\1.6 & Orion 1.3 CP2642-17
    £102.50 (inc VAT)
    (ex VAT) £85.42

    Part Number: CP2642-17

    Available from Stock (while stock lasts)
  18. Aluminium bellhousing: ZF gearbox to Ford 4 cylinder (RH starter) BH2A
    £528.00 (inc VAT)
    (ex VAT) £440.00

    Part Number: BH2A

    Normal side for BDA and X/Flow. Starter on RH side (inlet si.... Learn More
    Available From Stock
  19. Std clutch kit Ford X\Flow OHV Kent Escort Mk2 190mm 619001506
    £79.90 (inc VAT)
    (ex VAT) £66.58

    Part Number: 619001506

    3 piece standard duty clutch kit. Contains clutch cover, pla.... Learn More
    Available From Stock
Set Ascending Direction

1-20 of 41

Page
© 2001-2024 Burton Power. All Rights Reserved.